Deburrers

Thread deburrer, suitable for steel, brass, copper, aluminum and wood.

Materiál: Speciální nástrojová ocel

Ojehlovač , odhrotovač trubek a plechů. Univerzálně použitelný s noži typu S.

Suitable for hard work. Clamps all S-type knives (diameter 3.2mm)

Long lifetime. The scraper consists of an SG ergonomic handle and a ceramic convex knife CR (radius 250mm), which is non-replaceable.

Also suitable for surface scraping and deburring. The knife is replaceable. Knife material: Ceramic 1250HV Angle: 90 ° Use: surfaces and straight edges

Ideal for rounded edges. Replaceable knife. Knife material: Ceramic 1250HV Angle: 90 ° Use: surfaces and straight edges

The handle is equipped with hand protection. Round knives have a long service life, as they can be rotated and turned (they are ground on both sides). Only 1 knife is used for deburring in the corners. Range: 0-12mm.

Range: 1-11mm.

Hexagonal aluminum handle with non-replaceable knife type S10. The tool is designed for aluminum and plastics.

Possibility to clamp all knives type S and countersinks RD

The attachment allows you to clamp an S-type knife on one side and an N-type knife on the other. The attachment is telescopic: 20-94mm for S knives, 20-110mm for N knives

Upne všechny nože typu S (průměr 3,2mm).

Upne všechny nože typu S (průměr 3,2mm).

Range: 0-3mm (groove width)

The countersink allows easy chamfering of the edges of the holes. The countersink with 1 cutting edge guarantees smooth deburring.

Minimum diameter 9mm

Applicable to various materials

Universal use

Universal use

Škrabák s teleskopickým nástavcem pro malé nože.

Škrabák se záhlubníkem. Záhlubník použitelný ke srážení hran otvorů.

It can be used on sheets and metal plates for double-sided chamfering, with a thickness of 1-8 mm

Grooves from 3.5 mm. Possibility to clamp all L knives, including double-sided L7 knife

Can also be used on sheet metal. All knives L can be clamped. Range: 0-2.5mm

All knives L can be clamped

Range: 2,4-11mm

Continuous rotation of the countersink allows very fast deburring of the holes

Scraper for chamfering the outer edges of pipes and rods. Range: 8-28mm

Scraper suitable for toolmakers

Škrabák na odjehlování vnitřních otvorů.

Škrabák s vodítkem pro srážení rovných hran pod úhlem 45°.

Scraper with replaceable knife and with the possibility of clamping all S-type knives

Handle with replaceable knife S100 and with the possibility of clamping all knives type S and countersinks RD

Countersink for deburring the outer and inner edges of holes. Range: 3-5.5mm. How to replace a knife: Pull hard on the aluminum end of the handle until the thin hex key that fits into the screw holding the knife comes out.

Countersink for deburring the outer and inner edges of holes. Range: 5-10mm. How to replace a knife: Pull hard on the aluminum end of the handle until the thin hex key that fits into the screw holding the knife comes out.

Countersink for deburring the outer and inner edges of holes. Range: 10-22mm. How to replace a knife: Pull hard on the aluminum end of the handle until the thin hex key that fits into the screw holding the knife comes out.

Scraper with a double-sided triangular knife, which allows you to scrape and deburr most materials. The double-sided knife guarantees a longer service life. The length of the knife is freely adjustable.

Scraper with aluminum handle and double-sided triangular knife, which allows scraping and deburring of most materials.

The scraper with ergonomic handle allows you to clamp all knives type S and N, OR, TC, countersinks RD and EX18 in a "push and pull" manner.

With the help of 3 knives, it chamfers both the inner and outer edges of pipes and rods. The body is made of plastic. Applicable to aluminum, brass and copper. Range: 4-42mm.

It is equipped with a pocket clip and a replaceable knife. Clamps all N-type knives (diameter 2.6 mm).

Keramický škrabák na měkké plasty.

Keramický škrabák na tvrdé plasty.

Škrabák s jedním nožem.